Re: BIG WinBin vs TunerCat discrepencies

["Bruce Plecan" <nacelp@bright.net>]

Generally the bins can be refered to by mask ID.
128+256s at 0008
512s at 4008
This isn't an absolute, again the F to Y platforms have been known to vary,
with in the same mask ID.
Grumpy

> Aren't the .ecus for specific bins or groups of bins?? ( anyone got a 730
4cyl
> bin hacked, or a .ecu for one?)
>
> Previously, you (Programmer) wrote:
> { The *.ecu files are the problem...you'll have to rework your
> { own to correct them. I don't think anyone has posted a correct
> { 730 ECU for WinBin as yet--close, but not correct. The info for the
ECU's
> { have been taken from dissembled info--which must be incorrect ??
> { Lyndon.
> { -----Original Message-----
> { From: trax <trax@frederickmd.com>
> { To: Gmecm@Diy-Efi. Org <gmecm@diy-efi.org>
> { Cc: Nick Dedio <nickd_92@hotmail.com>
> { Date: June 14, 2000 3:28 PM
> { Subject: BIG WinBin vs TunerCat discrepencies
>

>

> { >FELP!  FELP!
> { >
> { >I thought that these discrepencies were just limited to what I
initially
> { >mentioned; namely, ...
> { >
> { >Coolant fan temps
> { >Injector flow rate
> { >Feul cutoff and return (RPM)
> { >Cold, Warm, and Hot closed loop timers
> { >
> { >But, there are much bigger fish in these waters :-(
> { >
> { >The VE tables (both) contain the same values ... BUT IN THE WRONG
CELLS!!!!
> { >Has anyone seen this before?  It looks like the tables are turned
sideways.
> { >The values in the 20kpa column for rpms 1600-4800 inside TunerCat are
the
> { >values in WinBin for 1600rpms for 20-100kpa!!!!  What the?
Furthermore,
> { >TunerCat has this table populated to 5600rpms and WinBin only goes to
> { >4800rpms.
> { >
> { >This discrepency is also true with the spark tables ... but, to a much
> { >bigger degree.  The tables don't even contain the same values :-(
> { >
> { >Does ANYONE know what is up with this?  FELP!
> { >
> { >Tim
> { >
>

>---------------------------------------------------------------------------
> { -
> { >To unsubscribe from gmecm, send "unsubscribe gmecm" (without the
quotes)
> { >in the body of a message (not the subject) to
majordomo@lists.diy-efi.org
> { >
>

>
 ---------------------------------------------------------------------------
-
> { To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> { in the body of a message (not the subject) to
majordomo@lists.diy-efi.org
>

>
> --
> Pat Ford                           email: pford@qnx.com
> QNX Software Systems, Ltd.           WWW: http://www.qnx.com
> (613) 591-0931      (voice)         mail: 175 Terence Matthews
> (613) 591-3579      (fax)                 Kanata, Ontario, Canada K2M 1W8
>
> --------------------------------------------------------------------------
--
> To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> in the body of a message (not the subject) to majordomo@lists.diy-efi.org
>
>

----------------------------------------------------------------------------
To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
in the body of a message (not the subject) to majordomo@lists.diy-efi.org