Esp the 165's.. 730 aren't so bad...
Mike Rolica
Plant A,
Magnesium Products Division
Strathroy
(519)-245-4040 Ext. 265
-----Original Message-----
From: Bruce Plecan [SMTP:nacelp@bright.net]
Sent: Thursday, June 15, 2000 11:15 AM
To: gmecm@diy-efi.org
Subject: Re: BIG WinBin vs TunerCat discrepencies
Generally the bins can be refered to by mask ID.
128+256s at 0008
512s at 4008
This isn't an absolute, again the F to Y platforms have been
known to vary,
with in the same mask ID.
Grumpy
> Aren't the .ecus for specific bins or groups of bins?? (
anyone got a 730
4cyl
> bin hacked, or a .ecu for one?)
>
> Previously, you (Programmer) wrote:
> { The *.ecu files are the problem...you'll have to rework
your
> { own to correct them. I don't think anyone has posted a
correct
> { 730 ECU for WinBin as yet--close, but not correct. The
info for the
ECU's
> { have been taken from dissembled info--which must be
incorrect ??
> { Lyndon.
> { -----Original Message-----
> { From: trax <trax@frederickmd.com>
> { To: Gmecm@Diy-Efi. Org <gmecm@diy-efi.org>
> { Cc: Nick Dedio <nickd_92@hotmail.com>
> { Date: June 14, 2000 3:28 PM
> { Subject: BIG WinBin vs TunerCat discrepencies
>
>
> { >FELP! FELP!
> { >
> { >I thought that these discrepencies were just limited to
what I
initially
> { >mentioned; namely, ...
> { >
> { >Coolant fan temps
> { >Injector flow rate
> { >Feul cutoff and return (RPM)
> { >Cold, Warm, and Hot closed loop timers
> { >
> { >But, there are much bigger fish in these waters :-(
> { >
> { >The VE tables (both) contain the same values ... BUT IN
THE WRONG
CELLS!!!!
> { >Has anyone seen this before? It looks like the tables
are turned
sideways.
> { >The values in the 20kpa column for rpms 1600-4800
inside TunerCat are
the
> { >values in WinBin for 1600rpms for 20-100kpa!!!! What
the?
Furthermore,
> { >TunerCat has this table populated to 5600rpms and
WinBin only goes to
> { >4800rpms.
> { >
> { >This discrepency is also true with the spark tables ...
but, to a much
> { >bigger degree. The tables don't even contain the same
values :-(
> { >
> { >Does ANYONE know what is up with this? FELP!
> { >
> { >Tim
> { >
>
>---------------------------------------------------------------------------
> { -
> { >To unsubscribe from gmecm, send "unsubscribe gmecm"
(without the
quotes)
> { >in the body of a message (not the subject) to
majordomo@lists.diy-efi.org
> { >
>
>
---------------------------------------------------------------------------
-
> { To unsubscribe from gmecm, send "unsubscribe gmecm"
(without the quotes)
> { in the body of a message (not the subject) to
majordomo@lists.diy-efi.org
>
>
> --
> Pat Ford email: pford@qnx.com
> QNX Software Systems, Ltd. WWW:
http://www.qnx.com
> (613) 591-0931 (voice) mail: 175 Terence
Matthews
> (613) 591-3579 (fax) Kanata, Ontario,
Canada K2M 1W8
>
>
--------------------------------------------------------------------------
--
> To unsubscribe from gmecm, send "unsubscribe gmecm"
(without the quotes)
> in the body of a message (not the subject) to
majordomo@lists.diy-efi.org
>
>
----------------------------------------------------------------------------
To unsubscribe from gmecm, send "unsubscribe gmecm" (without
the quotes)
in the body of a message (not the subject) to
majordomo@lists.diy-efi.org
<<application/ms-tnef>>